Diagnostic Tools
-
BENNING BENNING Multimeter MM 2-3 0.1 mV-1000 V AC, 0.1 mV-1000 V DC ( 4000828965 )
Sat, 07/26/2025
Scope of Delivery: - Multimeter MM 2-3 0.1 mV-1000 V AC, 0.1 mV-1000 V DC - Supplied with ergonomic housing with integrated rubber protection frame, bag, silicone measuring lead set (red/black, length: 1 m) with gold-plated 2 mm measuring tip and screw-on 4 mm lamellar measuring tip, wire temperature sensor, batteries (2 x type AAA) - for replacement batteries, see item no. 4000 901 810 - Product Description: 4-digit, illuminated LCD display (6.000 dots) - socket check (optical/acoustic, A range) with warning in case of incorrect measuring range selection - voltage sensor for non-contact and single-pole phase and cable break test (optical/acoustic) - automatic/manual range selection, switch-off, battery status display - measured value (HOLD), maximum/minimum/average value memory (MAX/ MIN/ AVG), relative measurement (REL) - measuring category CAT IV 300 V, CAT III 600 V, CAT III 1000 V measuring ranges: DC/AC voltage (10 µV - 1000 V), DC/AC current (1 mA - 10 A), resistance (0.1 Ω - 60 MΩ), frequency (10 Hz - 50 kHz), capacitance (0.01 nF - 10 mF), temperature (-40 °C - 400 °C) - optical and acoustic continuity ( Technical Data: - Width: 50mm - Length: 161mm - Height: 80mmNote on the disposal of batteries and rechargeable batteries - As we sell batteries and rechargeable batteries or devices containing batteries and rechargeable batteries, we are obliged under the Battery Act (BattG) to inform you of the following: The symbol of the crossed-out dustbin on batteries or accumulators means that they must not be disposed of with household waste after use. If batteries or accumulators contain mercury, cadmium or lead, you will find the respective chemical symbol (Hg, Cd or Pb) below the symbol of the crossed-out dustbin. Every user of batteries or accumulators is legally obliged to return old batteries and accumulators. You can do this free of charge at a retail outlet or other collection point in your area. You can obtain the addresses of suitable collection centres in your area from your city or local authority. For batteries that contain more than 0.0005 per cent mercury by mass, more than 0.002 per cent cadmium by mass or more than 0.004 per cent lead by mass, the chemical designations of the pollutant used can be found under the waste bin symbol. The chemical designations have the following meaning: Pb: Battery contains lead Cd: Battery contains cadmium Hg: Battery contains mercuryFor commercial use, please observe the building regulations!
-
BENNING BENNING Multimeter MM 2-2 0.1 mV-1000 V AC, 0.1 mV-1000 V DC ( 4000828964 )
Sat, 07/26/2025
Scope of Delivery: - Multimeter MM 2-2 0.1 mV-1000 V AC, 0.1 mV-1000 V DC - Supplied with ergonomic housing with integrated rubber protective frame, bag, high-quality silicone measuring lead set (red/black, length: 1 m) with gold-plated 2 mm measuring tip and screw-on 4 mm lamellar measuring tip, batteries (2 x type AAA) - for replacement batteries, see item no. 4000 901 810 Product Description: 4-digit, illuminated LCD display (6.000 dots) Socket control (optical/acoustic, A range) with warning in case of incorrect measuring range selection - Voltage sensor for non-contact and single-pole phase and cable break test (optical/acoustic) - Automatic/manual range selection, switch-off, battery status display - Measured value (HOLD), maximum/minimum/average value memory (MAX/ MIN/ AVG), relative measurement (REL) - Measuring category CAT IV 300 V, CAT III 600 V Measuring ranges: DC/AC voltage (10 µV - 1000 V), DC/AC current (1 mA - 10 A), resistance (0.1 Ω - 60 MΩ), frequency (10 Hz - 50 kHz), capacitance (0.01 nF - 10 mF) - optical and acoustic continuity ( Technical Data: - Width: 50mm - Length: 161mm - Height: 80mmNote on the disposal of batteries and rechargeable batteries - As we sell batteries and rechargeable batteries or devices containing batteries and rechargeable batteries, we are obliged under the Battery Act (BattG) to inform you of the following: The symbol of the crossed-out dustbin on batteries or accumulators means that they must not be disposed of with household waste after use. If batteries or accumulators contain mercury, cadmium or lead, you will find the respective chemical symbol (Hg, Cd or Pb) below the symbol of the crossed-out dustbin. Every user of batteries or accumulators is legally obliged to return old batteries and accumulators. You can do this free of charge at a retail outlet or other collection point in your area. You can obtain the addresses of suitable collection centres in your area from your city or local authority. For batteries that contain more than 0.0005 per cent mercury by mass, more than 0.002 per cent cadmium by mass or more than 0.004 per cent lead by mass, the chemical designations of the pollutant used can be found under the waste bin symbol. The chemical designations have the following meaning: Pb: Battery contains lead Cd: Battery contains cadmium Hg: Battery contains mercuryFor commercial use, please observe the building regulations!
-
BENNING BENNING Multimeter MM 7-2 1000 V ( 4000828962 )
Sat, 07/26/2025
Scope of Delivery: - Multimeter MM 7-2 1000 V - Supplied with ergonomic housing with integrated rubber protective frame, case, high-quality silicone measuring lead set (red/black, length: 1 m) with gold-plated 2 mm measuring tips and screw-on 4 mm lamellar measuring tips, wire temperature sensor, batteries (3 x type AAA), for replacement batteries see art. no. 4000 901 810 Product Description: 5-digit, illuminated LCD display (60.000 dots) with bar graph - TRUE RMS measurement method (AC, AC+DC) - AutoV function for automatic AC/DC switching and measuring range selection - Low input impedance (LoZ) for suppression of capacitive/inductive interspersed voltages - Socket control (optical/acoustic, µA/mA and A range) with warning message in case of incorrect measuring range selection - Low-pass filter (high frequency suppression HFR, 1000 Hz) for measurements on pulsed motor drives - Voltage sensor for non-contact and single-pole phase and cable break testing (optical/acoustic) - Automatic range selection, switch-off, battery status display - Measured value (HOLD/A-HOLD), maximum/minimum/average value memory (MAX/ MIN/ AVG), relative measurement (REL), peak value memory (PEAK) - Measurement category CAT IV 600 V, CAT III 1000 V Measuring ranges: DC/AC voltage (10 µV - 1000 V), DC/AC current (0.01 µA - 10 A), resistance (0.01 Ω - 60 MΩ), frequency (0.001 Hz - 50 kHz/ 1 MHz), capacitance (0.01 nF - 10 mF), duty cycle (%), 4 mA - 20 mA DC current loop (%), temperature (-200 °C - 1090 °C) - optical and acoustic continuity test ( Technical Data: - Width: 89mm - length: 193mm - subject to inspection: yes - Height: 51mmNote on the disposal of batteries and rechargeable batteries - As we sell batteries and accumulators or devices containing batteries and accumulators, we are obliged under the German Battery Act (BattG) to inform you of the following: The symbol of the crossed-out dustbin on batteries or accumulators means that they must not be disposed of with household waste after use. If batteries or accumulators contain mercury, cadmium or lead, you will find the respective chemical symbol (Hg, Cd or Pb) below the symbol of the crossed-out dustbin. Every user of batteries or accumulators is legally obliged to return old batteries and accumulators. You can do this free of charge at a retail outlet or other collection point in your area. You can obtain the addresses of suitable collection centres in your area from your city or local authority. For batteries that contain more than 0.0005 per cent mercury by mass, more than 0.002 per cent cadmium by mass or more than 0.004 per cent lead by mass, the chemical designations of the pollutant used can be found under the waste bin symbol. The chemical designations have the following meaning: Pb: Battery contains lead Cd: Battery contains cadmium Hg: Battery contains mercuryFor commercial use, please observe the building regulations!
-
BENNING BENNING current clamp multimeter CM 2-1 0.01 - 400 A ( 4000828956 )
Scope of Delivery: - Current clamp multimeter CM 2-1 0.01 - 400 A - Delivery incl. bag, test leads, batteries (2 x type AAA), spare batteries see art. 4000 901 810 Product Description: Illuminated 4-digit digital LCD display (4000 dots) - Light sensor - Continuity test - Diode test - AutoV function with low input impedance (LoZ) for suppressing reactive voltages - Low-pass filter (HFR high frequency suppression, 800 Hz) for measurements on pulsed motor drives - Voltage sensor (NCV) for non-contact phase and cable break testing (buzzer, LCD) - Automatic measuring range selection, switch-off, battery undervoltage display - Instantaneous value memory Hold - Minimum/maximum value memory MIN/MAX, zero adjustment (ZERO) - Measuring circuit category Cat IV 300 V, Cat III 600 V Measuring ranges: DC/AC current 10 mA - 400 A, DC/AC voltage 0.1 mV - 600 V, resistance 0.1 Ohm - 40 MOhm, frequency 1 Hz - 50 kHz, capacitance 0.001 µF - 100 000 µF Technical Data: - Width: 56mm - Length: 188mm - Pliers opening: 27mm - Height: 28mmNote on the disposal of batteries and rechargeable batteries - As we sell batteries and accumulators or devices containing batteries and accumulators, we are obliged under the Battery Act (BattG) to draw your attention to the following: The symbol of the crossed-out dustbin on batteries or accumulators means that they must not be disposed of with household waste after use. If batteries or accumulators contain mercury, cadmium or lead, you will find the respective chemical symbol (Hg, Cd or Pb) below the symbol of the crossed-out dustbin. Every user of batteries or accumulators is legally obliged to return old batteries and accumulators. You can do this free of charge at a retail outlet or other collection point in your area. You can obtain the addresses of suitable collection centres in your area from your city or local authority. For batteries that contain more than 0.0005 per cent mercury by mass, more than 0.002 per cent cadmium by mass or more than 0.004 per cent lead by mass, the chemical designations of the pollutant used can be found under the waste bin symbol. The chemical designations have the following meaning: Pb: Battery contains lead Cd: Battery contains cadmium Hg: Battery contains mercuryFor commercial use, please observe the building regulations!
-
BENNING BENNING insulation/resistance tester IT 100 600 V ( 4000828961 )
Sat, 07/26/2025
Scope of Delivery: - Insulation/resistance tester IT 100 600 V - Supplied with rubber protection frame, bag, test leads, crocodile clips, batteries (4 x type AA), spare batteries see art. no. 4000 901 811 Product Description: for insulation and low-resistance measurements on electrical systems, devices, cables, motors and generators - 4-digit, illuminated LCD display (9,999 dots) - red LED for test/external voltage - automatic discharge of capacitive voltages - zero balancing of test leads - lock function for continuous insulation and low-resistance measurement - integrated fuse test - test lock for reverse voltage - measurement category CAT IV 600 V Measuring ranges: Low-resistance measurement up to 60 Ω, insulation resistance up to 20 GΩ (test voltage: 50 V, 100 V, 250 V, 500 V, 1000 V) and resistance measurement with 200 mA test current (testing of protective conductor connections), polarisation index (PI), dielectric absorption rate (DAR), voltage (600 V), resistance (600 kΩ) Technical Data: - Width: 89mm - Length: 206mm - Batteries: 4 x Mignon type AA - Low-impedance resistance: 0.01 Ω-60 Ω - Resistance: 600 kΩ - Insulation resistance: 300 kΩ-20 GΩ - Voltage: 600V - Measured value memory: false - Height: 51mm - Display: 9.999 digit (illuminated)Note on the disposal of batteries and rechargeable batteries - As we sell batteries and rechargeable batteries or devices containing batteries and rechargeable batteries, we are obliged under the Battery Act (BattG) to inform you of the following: The symbol of the crossed-out dustbin on batteries or accumulators means that they must not be disposed of with household waste after use. If batteries or accumulators contain mercury, cadmium or lead, you will find the respective chemical symbol (Hg, Cd or Pb) below the symbol of the crossed-out dustbin. Every user of batteries or accumulators is legally obliged to return old batteries and accumulators. You can do this free of charge at a retail outlet or other collection point in your area. You can obtain the addresses of suitable collection centres in your area from your city or local authority. For batteries that contain more than 0.0005 per cent mercury by mass, more than 0.002 per cent cadmium by mass or more than 0.004 per cent lead by mass, the chemical designations of the pollutant used can be found under the waste bin symbol. The chemical designations have the following meaning: Pb: Battery contains lead Cd: Battery contains cadmium Hg: Battery contains mercuryFor commercial use, please observe the building regulations!
-
BENNING BENNING Multimeter MM 5-2 0.1 mV-600 V AC/DC ( 4000828866 )
Sat, 07/26/2025
Scope of Delivery: - Multimeter MM 5-2 0.1 mV-600 V AC/DC - Supplied with batteries (2 x type AAA), test leads, rubber protection frame with magnetic hanger, wire temperature sensor, case, spare batteries see art. no. 4000 901 810 Product Description: with illuminated 4-digit LCD display (6000 dots) - micro-ampere measuring ranges (400.0 µA DC/ 4000 µA DC) - continuity test via red LED and buzzer - diode test - integrated voltage sensor signals phase voltages and cable breaks in lines without contact (optical) - single-pole phase test - automatic range selection - automatic switch-off - measured value (HOLD), peak value memory (PMAX/ PMIN), relative measurement (REL) - measurement category CAT IV 300 V, CAT III 600 V - measurement ranges: DC voltage: 100 µV - 600 V, AC voltage: 100 µV - 600 V. Direct current: 0.1 µA - 10 A, alternating current: 20 mA - 10 A, resistance: 0.1 Ω - 40 MΩ. Frequency: 0.01 Hz - 50 kHz, capacitance: 0.01 nF - 1 mF, temperature: - 40 °C to + 400 °C Technical Data: - Width: 77mm - Length: 150mm - Height: 44mmNote on the disposal of batteries and rechargeable batteries - As we sell batteries and accumulators or devices containing batteries and accumulators, we are obliged under the Battery Act (BattG) to inform you of the following: The symbol of the crossed-out dustbin on batteries or accumulators means that they must not be disposed of with household waste after use. If batteries or accumulators contain mercury, cadmium or lead, you will find the respective chemical symbol (Hg, Cd or Pb) below the symbol of the crossed-out dustbin. Every user of batteries or accumulators is legally obliged to return old batteries and accumulators. You can do this free of charge at a retail outlet or other collection point in your area. You can obtain the addresses of suitable collection centres in your area from your city or local authority. For batteries that contain more than 0.0005 per cent mercury by mass, more than 0.002 per cent cadmium by mass or more than 0.004 per cent lead by mass, the chemical designations of the pollutant used can be found under the waste bin symbol. The chemical designations have the following meaning: Pb: Battery contains lead Cd: Battery contains cadmium Hg: Battery contains mercuryFor commercial use, please observe the building regulations!
-
BENNING BENNING CM 11 current clamp multimeter 0.1 mA-20 A AC, 0.1 mA-10 A DC ( 4000828923 )
Sat, 07/26/2025
Scope of Delivery: - Current clamp multimeter CM 11 0.1 mA-20 A AC, 0.1 mA-10 A DC - Supplied with batteries (2 x type AAA), test leads and bag, for spare batteries see art. no. 4000 901 810 Product Description: Illuminated 4-digit LCD display (6.000 dots) - precise measurement of small AC/DC currents with the highest resolution of 0.1 mA - ideal for troubleshooting in electrical systems, control systems, devices and vehicle electrics - troubleshooting and quiescent current measurement in fire alarm and intruder alarm systems - measurement of leakage, differential and leakage currents - measurement of 4 mA - 20 mA process signals without interrupting the current loop leakage currents - measurement of 4 mA - 20 mA process signals without interrupting the current loop - quiescent current measurement on vehicle batteries to check for creeping battery discharge - precise measurement of load currents up to 20 A AC/ 10 A DC - continuity test - automatic switch-off (APO after 15 min., can be deactivated) - battery undervoltage display - measured value memory (HOLD), minimum/maximum value memory (MIN/ MAX), ZERO function - measurement category CAT IV 300 V, CAT III 600 V - measuring ranges: Direct current: 0.1 mA - 10 A (measuring ranges 300.0 mA / 3.000 A / 10.00 A) Alternating current: 0.1 mA - 20 A (measuring ranges 300.0 mA / 3.000 A / 20.00 A) Voltage: 0.01 V - 600 V, resistance: 0.1 Ω - 600 kΩ Technical Data: - Width: 76mm - Length: 206mm - Pliers opening: 23mm - Height: 33.5mmNote on the disposal of batteries and rechargeable batteries - As we sell batteries and accumulators or devices containing batteries and accumulators, we are obliged under the Battery Act (BattG) to draw your attention to the following: The symbol of the crossed-out dustbin on batteries or accumulators means that they must not be disposed of with household waste after use. If batteries or accumulators contain mercury, cadmium or lead, you will find the respective chemical symbol (Hg, Cd or Pb) below the symbol of the crossed-out dustbin. Every user of batteries or accumulators is legally obliged to return old batteries and accumulators. You can do this free of charge at a retail outlet or other collection point in your area. You can obtain the addresses of suitable collection centres in your area from your city or local authority. For batteries that contain more than 0.0005 per cent mercury by mass, more than 0.002 per cent cadmium by mass or more than 0.004 per cent lead by mass, the chemical designations of the pollutant used can be found under the waste bin symbol. The chemical designations have the following meaning: Pb: Battery contains lead Cd: Battery contains cadmium Hg: Battery contains mercuryFor commercial use, please observe the building regulations!
-
KS Tools KS TOOLS 4,0 mm Eingangsbuchse auf nadelförmige Prüfspitze, rot ( 150.1674 )
Sat, 07/26/2025
Produktbeschreibung:4,0 mm Eingangsbuchse auf nadelförmige Prüfspitze, rot · Nadelförmige PrüfspitzeMerkmale: isoliert universal einsetzbar ideal zum Überprüfen schmaler und dünner Kabel, z.B. Anzeigegeräten mit 4,0 mm Eingangsbuchse anwendbar bis maximal 24V (10A) Kabellänge 200,0 mm Technische Daten: - Farbe: rot - Funktions-Attribut 1: zum Prüfen elektrischer Probleme - Gewicht [g]: 10 g - Herstellernummer: 150.1674 - Kabellänge in mm: 200.0 mm
-
KS Tools KS TOOLS Kompressions-Druckprüfgerät für Dieselmotoren mit Diagrammschreiber ( 150.1662 )
Produktbeschreibung:Kompressions-Druckprüfgerät für Dieselmotoren mit Diagrammschreiber · Merkmale:Technische Daten: - Anwendungsbereich allgemein: Diesel - Gewicht [g]: 839 g - Herstellernummer: 150.1662
-
KS Tools KS TOOLS Kompressions-Druckprüfgerät für Benzinmotoren mit Diagrammschreiber ( 150.1659 )
Produktbeschreibung:Kompressions-Druckprüfgerät für Benzinmotoren mit Diagrammschreiber · Merkmale:Technische Daten: - Anwendungsbereich allgemein: Benzin - Gewicht [g]: 917 g - Herstellernummer: 150.1659
-
REMS REMS Push Hand Druckprüfpumpe mit Manometer 6 MPa / 60 bar / 870 psi 1/2" ( 115000 R )
Lieferumfang:- 1x REMS Push Hand DruckprüfpumpeProduktbeschreibung:REMS bietet hier mit der REMS Push eine Hand Druckprüfpumpe mit der man einfach und unkompliziert den Druck und die Dichtheit von Rohrleitungen und Behältern überprüfen kann. Die REMS Push verfügt über einen korrosionsbeständigen und pulverbeschichteten Stahlblechbehälter für bis zu 12 Liter Füllmenge und einen 1,5 Meter langen Hochdruckschlauch mit einem 1/2" Anschluss. REMS ist ein führender Hersteller von Werkzeugen zur Rohrverarbeitung, eine lange Tradition sowie eine stets gute Verarbeitungsqualität zeichnen das Unternehmen aus.Technische Daten:Hersteller: REMSHerstellerbezeichnung: REMS PushHerstellernummer: 115000 Rmax. Druck: 6 MPa / 60 bar / 870 psi Bei gewerblicher Nutzung beachten Sie bitte die Bauvorschriften!
-
Laserliner Laserliner VideoFlex G3 Micro 6 mm 1,5m Kabel Inspektionskamera Endoskopkamera Kamerasonde ( 082.211A )
Lieferumfang:- 1x Laserliner VideoFlex G3 Kamera- 1x 1,5 m FlexCamera G3 Kabel- 1x HardCase-Transportkoffer- 1x 4 GB Micro-SD-Karte- 1x Li-Ion Akkupack - 1x TopClips G3- 1x TopGuide G3- Software- 1x Videoverbindungskabel- Netz-/Ladegerät mit internationalen AdapternProduktbeschreibung:Die Laserliner VideoFlex G3 Micro Inspektionskamera eignet sich besonders zur Problemlokalisierung in Gegenständen, Wände, Leitungen Kabeln und an weiteren, schwer zugänglichen Orten. Durch LEDs am Kamerakopf und einem Durchmesser von 6 mm sind selbst dunkle, unzugängliche Stelle mit schlechten Lichtverhältnissen kein Problem. Durch die REC-Funktion ist eine spätere Auswertung durch Aufnahme und Speicherung direkt am Gerät möglich. Umfangreiche Funktionen am Monitor, wie die Bildrotation, welche das Bild auf dem integrierten LC-Displays um 180° drehen kann oder die Mirrorfunktion, die spiegelbildliche Aufnahmen korrigiert, komplettieren die Micro Inspektionskamera. Technische Daten:Kamerakopf-Ø: 6 mmKabel: 1,5 mKamerafokus: F1 cm - F6 cmBildschirmtyp: 3,5" TFT FarbdisplayAuflösung Kamera: 640 x 480 PixelAuflösung Display: 320 x 240 PixelAuflösung Bild / Videoformat: JPEG / AVILED: 4 hochleistungs LEDs mit 10 HelligkeitsstufenZoom: 1,5-fach Digitalzoom in 10% SchrittenSpeicher: Unterstütz SDHC-Card bis max. 8 GB SpeicherLänge-Flexschlauch: 1,5 MeterSchnittstelle: Mini-USBAnschlüsse: Micro-SD, Analog-VideoStromversorgung: Li-Ion Akkupack 3,7 V / 1,7 Ah / Netzteil 5 V / 1 AhLadezeit: ca. 4 Std.Betriebsdauer: ca 4 Std. Bei gewerblicher Nutzung beachten Sie bitte die Bauvorschriften!
I18n Error: Missing interpolation value "number1" for "You have seen {{ number1 }} out of {{ number2 }} products"