Only this week: 10% off all BOSCH power tools - discount will be deducted in the shopping cart

Description

SKU: 123156
EAN: 4007220297384

Scope of Delivery:
- Fan sander Z-COOL Ø40xH20mm grit size 80

Product Description:
zirconium aluminium oxide - for machining stainless steels and high-temperature alloys - high grinding performance - no clogging of the flaps - for coarse grinding tasks with high cutting performance and cool grinding - abrasive additives in the coating achieve a significantly higher stock removal rate, prevent clogging and result in cooler grinding - shank Ø 6 mm

Technical Data:
- Shank Ø: 6mm
- Drive type: Straight grinder, flexible shaft drive
- Application recommendation: Use grinding oil suitable for the material to significantly increase the service life and grinding performance of the tools. For best performance, use at a recommended cutting speed of 15-20 m/s. This achieves an ideal compromise between stock removal rate, surface finish, temperature load on the workpiece and tool wear. Increasing the cutting speed results in a slightly finer surface finish. Increasing the contact pressure results in a slightly coarser surface. The softer the material to be machined, the coarser the surface (when using , Reducing the contact pressure and the peripheral speed and adding grinding oil reduce tool wear and the temperature load on the workpiece. An increase in the stock removal rate should be achieved by using a coarser grit size and not by increasing the contact pressure in order to prevent unnecessary tool wear and thermal stress on the workpiece.
- Machinable materials: Copper, malleable cast iron, brass, bronze, cobalt-based alloys, grey/spheroidal cast iron (GG/GJL, GGG/GJS), hardened, tempered steels over 1,200 N/mm² ( 54 HRC, steels up to 1,200 N/mm² (< 38 HRC), titanium, cast steel
- Machining tasks: Structuring (matting, line matting and satin finishing), surface processing, deburring, levelling, fine grinding in stages, weld seam processing
- Width: 20mm
- Note: PFERDERGONOMICS recommends flap discs in order to sustainably reduce the vibration and noise generated during use and to improve working comfort.
- Length, shaft: 40mm
- RPM, opt.: 9600RPM
- Safety instructions: For safety reasons, the specified maximum permissible speed must never be exceeded. The contact pressure must be significantly reduced if the specified optimum speed is exceeded. Safety is only guaranteed if the clamping length is at least 15 mm and the specified maximum speed is not exceeded with open shank lengths.
- Advantages: Optimum contour adaptation due to high flexibility. Consistently high material removal rate over the entire service life, as new, aggressive abrasive is constantly released. Can be used very close to edges and at angles thanks to the flat cast core design.

For commercial use, please observe the building regulations!

Product form

PFERD flap disc Z-COOL Ø40xH20mm grit size 80 ( 4144150315 )

  • Vendor PFERD
  • condition  New
  • Unzufrieden? 100 Tage kostenfreie Retoure
  • Shipped today? Order within: Oct 05, 2025 14:00:00 +0200

Information on importing to Switzerland! 🇨🇭🇱🇮 We take care of customs clearance. You will receive your package as normal within the delivery time and you don't have to worry about anything. Your invoice includes Swiss VAT. Placing an order with us feels like a normal domestic order for you. The same goes for returns!

CHF 44.19
incl. VAT, plus shipping

As a member you will receive [points_amount]

in stock delivery expected in  Fri, 10/10/2025

    • American Express
    • Apple Pay
    • Google Pay
    • PayPal
    • Klarna
    • Mastercard
    • +12 weitere

    +780.000 BROs folgen uns auf

    Smarte Produktberatung

     
    • Responsible Person for the EU (GPSR) EU-based economic operator that ensures the product complies with the necessary regulations.
      • info@pferd.com
      • +49226490
      • Germany
      • 51709 Marienheide
      • Hauptstr. 13
      • August Rüggeberg GmbH&Co. KG Pferd - Werkzeuge

    Description

    SKU: 123156
    EAN: 4007220297384

    Scope of Delivery:
    - Fan sander Z-COOL Ø40xH20mm grit size 80

    Product Description:
    zirconium aluminium oxide - for machining stainless steels and high-temperature alloys - high grinding performance - no clogging of the flaps - for coarse grinding tasks with high cutting performance and cool grinding - abrasive additives in the coating achieve a significantly higher stock removal rate, prevent clogging and result in cooler grinding - shank Ø 6 mm

    Technical Data:
    - Shank Ø: 6mm
    - Drive type: Straight grinder, flexible shaft drive
    - Application recommendation: Use grinding oil suitable for the material to significantly increase the service life and grinding performance of the tools. For best performance, use at a recommended cutting speed of 15-20 m/s. This achieves an ideal compromise between stock removal rate, surface finish, temperature load on the workpiece and tool wear. Increasing the cutting speed results in a slightly finer surface finish. Increasing the contact pressure results in a slightly coarser surface. The softer the material to be machined, the coarser the surface (when using , Reducing the contact pressure and the peripheral speed and adding grinding oil reduce tool wear and the temperature load on the workpiece. An increase in the stock removal rate should be achieved by using a coarser grit size and not by increasing the contact pressure in order to prevent unnecessary tool wear and thermal stress on the workpiece.
    - Machinable materials: Copper, malleable cast iron, brass, bronze, cobalt-based alloys, grey/spheroidal cast iron (GG/GJL, GGG/GJS), hardened, tempered steels over 1,200 N/mm² ( 54 HRC, steels up to 1,200 N/mm² (< 38 HRC), titanium, cast steel
    - Machining tasks: Structuring (matting, line matting and satin finishing), surface processing, deburring, levelling, fine grinding in stages, weld seam processing
    - Width: 20mm
    - Note: PFERDERGONOMICS recommends flap discs in order to sustainably reduce the vibration and noise generated during use and to improve working comfort.
    - Length, shaft: 40mm
    - RPM, opt.: 9600RPM
    - Safety instructions: For safety reasons, the specified maximum permissible speed must never be exceeded. The contact pressure must be significantly reduced if the specified optimum speed is exceeded. Safety is only guaranteed if the clamping length is at least 15 mm and the specified maximum speed is not exceeded with open shank lengths.
    - Advantages: Optimum contour adaptation due to high flexibility. Consistently high material removal rate over the entire service life, as new, aggressive abrasive is constantly released. Can be used very close to edges and at angles thanks to the flat cast core design.

    For commercial use, please observe the building regulations!

    Recently Viewed

    Top questions at a glance

    How can I pay for my order?

    We offer a wide range of secure payment methods:

    online payment methods

    PayPal, KLARNA, Google Pay, Apple Pay and Shop Pay.

    Credit cards

    You can also pay with the major credit cards VISA, MasterCard and American Express. In this case, the payment is secured using the 3D-Secure method. If we have any reason to suspect fraudulent ordering, we will automatically cancel the payment.

    How can I pay for my order?
    How do I receive an invoice?

    You will automatically receive the invoice from our shipping partner in a separate email after receipt of payment. It will not come with the confirmation of receipt. In addition, a paper invoice will be enclosed with the order.

    Therefore, please also check your spam folder again thoroughly and otherwise get in touch here in our invoice portal.

    How do I receive an invoice?
    Returns: I want to return something

    If you wish to return all or part of your order and you're from the EU 🇪🇺, please check our returns portal.

    For returns from Switzerland 🇨🇭 and Liechtenstein 🇱🇮, use this returns portal.

    Where is my order?

    There are various ways to track the shipment status:

    The dispatch usually takes 1 - 2 working days. If it takes longer or you think the parcel has disappeared, please contact us here in our problem portal.

    Your tool family

    • <strong>Personalized support</strong>

      Personalized support

      Unlike many other platforms, we offer you personal advice and service that supports you at all times.

    • <strong></strong>

    • <strong>Best Prices</strong>

      Best Prices

      For each item with this symbol, you will currently receive the best online price (for the german market) from us. You can find the exact information on this on the product pages.

    This is Toolbrothers

    Tools are the engine of our society. Whether you're building a house, bought an IKEA cabinet or finally want to fix that leaky faucet, you need tools. We provide you with tools – and in true Toolbrothers style.

    • Super fast
    • Reliable
    • With the best service

    Log in

    Forgot your password?

    Don't have an account yet?
    Create account