Neueste Artikel
-
PFERD PFERD POLICAP sanding cap carrier D16xH26mm ( 4000842551 )
Fri, 10/10/2025
Scope of Delivery: - POLICAP sanding cap carrier D16xH26mm Product Description: made of rubber - for holding POLICAP abrasive caps Technical Data: - nanFor commercial use, please observe the building regulations!
CHF 12.88
-
PFERD PFERD POLICAP sanding cap carrier D13xH17mm ( 4000842550 )
Fri, 10/10/2025
Scope of Delivery: - POLICAP sanding cap carrier D13xH17mm Product Description: made of rubber - for holding POLICAP abrasive caps Technical Data: - nanFor commercial use, please observe the building regulations!
CHF 12.74
-
PFERD PFERD flap disc Ø20xH10mm grit size 120 ( 4000842517 )
Fri, 10/10/2025
Scope of Delivery: - Flap sander Ø20xH10mm grit size 120 Product Description: Synthetic resin bond - universally applicable - also suitable for machining brass, copper and zinc - Shank ∅ 3 mm Technical Data: - Shank Ø: 3mm - Drive type: Straight grinder, flexible shaft drive - Application recommendation: Reducing the contact pressure and peripheral speed and adding grinding oil reduces tool wear and the temperature load on the workpiece. Increasing the cutting speed results in a slightly finer surface finish. Increasing the contact pressure makes the surface slightly coarser. The softer the material to be machined, the coarser the surface (when using , For best performance, use at a recommended cutting speed of 15-20 m/s. This achieves an ideal compromise between stock removal rate, surface finish, temperature load on the workpiece and tool wear. Use a suitable grinding oil for the material in order to significantly increase the service life and grinding performance of the tools. The removal rate should be increased by using a coarser grit and not by increasing the contact pressure in order to prevent unnecessary tool wear and thermal stress on the workpiece. - Machinable materials: Steel materials with a hardness > 54 HRC, cast steel, aluminium, malleable cast iron, brass, steels up to 1,200 N/mm² ( - Machining tasks: Gradual fine grinding, structuring (matting, line matting and satin finishing), deburring, levelling, weld seam processing, surface processing - Width: 10mm - Note: PFERDERGONOMICS recommends flap discs in order to sustainably reduce the vibration and noise generated during use and to improve working comfort. - Length, shaft: 40mm - RPM, opt.: 19000RPM - Safety instructions: For safety reasons, the specified maximum permissible speed must never be exceeded. The contact pressure must be significantly reduced if the specified optimum speed is exceeded. Safety is only guaranteed if the clamping length is at least 15 mm and the specified maximum speed is not exceeded with open shank lengths. - Advantages: Can be used very close to edges and at angles thanks to the flat casting core design. Consistently high material removal over the entire service life, as new, aggressive abrasive is constantly released. Optimum contour adaptation due to high flexibility.For commercial use, please observe the building regulations!
CHF 9.18
-
PFERD PFERD POLICAP sanding cap carrier D7xH13mm ( 4000842449 )
Fri, 10/10/2025
Scope of Delivery: - POLICAP sanding cap carrier D7xH13mm Product Description: made of rubber - for holding POLICAP abrasive caps Technical Data: - nanFor commercial use, please observe the building regulations!
CHF 12.68
-
PFERD PFERD POLICAP sanding cap carrier D5xH11mm ( 4000842448 )
Fri, 10/10/2025
Scope of Delivery: - POLICAP sanding cap carrier D5xH11mm Product Description: made of rubber - for holding POLICAP abrasive caps Technical Data: - nanFor commercial use, please observe the building regulations!
CHF 12.27
-
PFERD PFERD POLICAP sanding cap carrier D13xH17mm ( 4000842447 )
Fri, 10/10/2025
Scope of Delivery: - POLICAP sanding cap carrier D13xH17mm Product Description: made of rubber - for holding POLICAP abrasive caps Technical Data: - nanFor commercial use, please observe the building regulations!
CHF 12.74
-
PFERD PFERD POLICAP sanding cap carrier D7xH12mm ( 4000842446 )
Scope of Delivery: - POLICAP sanding cap carrier D7xH12mm Product Description: made of rubber - for holding POLICAP abrasive caps Technical Data: - nanFor commercial use, please observe the building regulations!
-
PFERD PFERD POLICAP sanding cap D13xH17mm grit 60 ( 4000842428 )
Scope of Delivery: - POLICAP sanding cap D13xH17mm grit 60 Product Description: Aluminium oxide A - abrasive cloth coated with aluminium oxide - for use in tool and mould making - for finishing work in hard-to-reach areas - for universal use on steel materials (hardened, tempered, unhardened) - specially developed for special tasks and for corresponding repair work - also suitable for processing plastics, wood and filler in model making - supplied without rubber backing Technical Data: - nanFor commercial use, please observe the building regulations!
-
PFERD PFERD flap disc POLIFAN A-COOL SG INOX+ALU Ø 125 mm grain size 80 conical ( 4000842357 )
Fri, 10/10/2025
Scope of Delivery: - Flap disc POLIFAN A-COOL SG INOX+ALU Ø 125 mm grain size 80 conical Product Description: Aluminium oxide - for machining stainless steel (INOX) and aluminium - with active grinding coating - for grinding tasks to achieve a high surface quality with low heat load - particularly cool grinding on materials with poor thermal conductivity - bore 22.23 mm Ø Technical Data: - Bore: 22,23mmFor commercial use, please observe the building regulations!
CHF 60.57
-
KLINGSPOR KLINGSPOR flap disc SMT 624 Supra Ø 125 mm grain size 120 12° conical ( 4000842317 )
Fri, 10/10/2025
Scope of Delivery: - Flap disc SMT 624 Supra Ø 125 mm grit 120 12° conical Product Description: zirconium aluminium oxide - for processing edges and weld seams on stainless steel (INOX) and steel - uniform grinding pattern - high stock removal rate - bore 22.23 mm Ø Technical Data: - Bore: 22,23mmFor commercial use, please observe the building regulations!
CHF 32.21
-
KLINGSPOR KLINGSPOR flap disc SMT 624 Supra Ø 125 mm grain size 80 12° conical ( 4000842316 )
Fri, 10/10/2025
Scope of Delivery: - Flap disc SMT 624 Supra Ø 125 mm grain size 80 12° conical Product Description: zirconium aluminium oxide - for processing edges and weld seams on stainless steel (INOX) and steel - uniform grinding pattern - high stock removal rate - bore 22.23 mm Ø Technical Data: - Bore: 22,23mmFor commercial use, please observe the building regulations!
CHF 32.21
-
KLINGSPOR KLINGSPOR flap disc SMT 624 Supra Ø 125 mm grain size 60 12° conical ( 4000842315 )
Fri, 10/10/2025
Scope of Delivery: - Flap disc SMT 624 Supra Ø 125 mm grain size 60 12° conical Product Description: zirconium aluminium oxide - for processing edges and weld seams on stainless steel (INOX) and steel - uniform grinding pattern - high stock removal rate - bore 22.23 mm Ø Technical Data: - Bore: 22,23mmFor commercial use, please observe the building regulations!
CHF 32.21
I18n Error: Missing interpolation value "number1" for "You have seen {{ number1 }} out of {{ number2 }} products"